Tuberculin - PPD Bovis, Intradermic.

Checkout our iOS App for a better way to browser and research.

§ 113.409 Tuberculin - PPD Bovis, Intradermic.

Tuberculin - PPD Bovis, Intradermic is a purified protein derivative produced from cultures of Mycobacterium bovis Strain AN-5 (supplied by Animal and Plant Health Inspection Service), which has been inactivated and is nontoxic. Each serial shall be tested for purity, safety, potency, and special chemical characteristics in accordance with the conditions prescribed for each test. A serial found unsatisfactory by any prescribed test shall not be released.

(a) Purity test. Each serial shall be tested for viable bacteria and fungi as prescribed in § 113.26.

(b) Safety test. Final container samples of completed product from each serial shall be tested for safety as prescribed in § 113.38.

(c) Potency test. Bulk or final container samples of completed product from each serial shall be subjected to a comparison specificity test using a Reference PPD Tuberculin supplied by Animal and Plant Health Inspection Service.

(1) Test animals. White female guinea pigs from one source, which weigh 500 to 700 grams at the beginning of the test, and which have not been used in a previous test, shall be used in the specificity test. Twenty-three guinea pigs (10 sensitized with M. bovis, 10 sensitized with M. avium and three unsensitized) shall be required for each serial being tested, and 20 guinea pigs (10 sensitized with M. bovis and 10 sensitized with M. avium) shall be required for the Reference PPD Tuberculin. Allowance should be made for deaths during the sensitization period.

(2) Sensitization of guinea pigs.

(i) Sensitize one group of guinea pigs to M. bovis. Inject each animal intramuscularly with 0.5 ml of a sterile heat-killed suspension of M. bovis Strain AN-5 supplied by Animal and Plant Health Inspection Service.

(ii) Sensitize one group of guinea pigs to M. avium. Inject each animal intramuscularly with 0.5 ml of a sterile heat-killed suspension of M. avium Strain D-4 supplied by Animal and Plant Health Inspection Service.

(iii) Maintain an unsensitized group as control animals.

(3) Thirty-five days post-injection, the guinea pigs shall be used for tuberculin testing.

(4) The sensitized animals and controls shall be prepared at least 4 hours prior to injection of PPD tuberculin by clipping the hair from the entire abdominal and flank areas, applying a depilatory agent for 5 to 10 minutes, then rinsing with warm water and drying.

(i) Select four sites on each guinea pig for injection of PPD tuberculin. Two sites shall be on each side of the midline and spaced a sufficient distance from each other to avoid overlapping of skin reactions.

(ii) Prepare four dilutions of the Reference PPD Tuberculin and each serial of PPD tuberculin being tested so as to contain 0.6, 1.2, 2.4, and 4.8 micrograms of protein per 0.1 ml dose. Each of the four dilutions of the same tuberculin shall be randomly assigned a site on a guinea pig.

(iii) Inject one dose of each dilution at the assigned site using a tuberculin syringe.

(5) Measurement of skin reactions. Measure the area of erythema produced at each site on each guinea pig 24 hours following injection of PPD tuberculin. Measurements in millimeters shall be made anterior to posterior across the greatest diameter and perpendicular to the first measurement. Calculate the area of erythema in square millimeters at each site by multiplying the two measurements.

(6) Calculation of average response per guinea pig. Obtain the total area of erythema for each guinea pig by adding the areas of the four test sites. Add these composite areas of erythema from all guinea pigs with the same sensitization and the same PPD tuberculin injection, then divide by the number of animals in the group. The number obtained is the average response per guinea pig to the PPD tuberculin for the given type of sensitization.

(7) Determination of specificity index. The specificity index of a PPD tuberculin is determined by subtracting the average response obtained on M. avium sensitized guinea pigs from the average response obtained on M. bovis sensitized guinea pigs.

(8) Validity of bioassay. The bioassay test results obtained on serials tested concurrently in a single test series are valid if the specificity index of the reference PPD tuberculin is at least 400 square millimeters. If the results are not valid, the bioassay test series must be repeated with a different set of sensitized guinea pigs.

(9) Reactions in unsensitized guinea pigs. If a positive reaction (erythema) is observed in one or more of the 3 unsensitized guinea pigs, the serial is unsatisfactory.

(10) Interpretation of specificity index. When a bioassay is valid and reactions are not observed in unsensitized guinea pigs, the following interpretation of the specificity index will be used for classifying each serial of PPD tuberculin:

Expand Table
Specificity index Classification
440 mm2 or greater Satisfactory.
Between 360 mm2 and 440 mm2 Inconclusive.
Less than 360 mm2 Unsatisfactory.

(11) Second stage test. If a serial is classified as inconclusive, it can be declared unsatisfactory or undergo a second stage test. The second stage shall be conducted in a manner identical to the first stage, except that unsensitized guinea pig controls are not necessary. The results are evaluated by combining the results obtained on all guinea pigs tested in stages one and two. Calculate the average response on the 20 M. bovis sensitized animals and on the 20 M. avium sensitized animals and determine the specificity index. An inconclusive serial is satisfactory after the second stage test, if its specificity index is 400 square millimeters or more, and unsatisfactory if its specificity index is less than 400 square millimeters.

(d) Special chemical tests and requirements. Final container samples of completed product from each serial shall be tested as follows:

(1) Protein concentration. The final product shall contain a protein concentration of 1.0 ±0.1 mg/ml. The Microkjeldahl Test for Nitrogen shall be used.

(2) Phenol content. Phenol content of the final product shall be 0.50 percent plus or minus 0.04 percent. A direct titration with a standardized bromide-bromate solution shall be conducted.

[41 FR 8471, Feb. 27, 1976, as amended at 41 FR 21760, May 28, 1976; 41 FR 32883, Aug. 6, 1976. Redesignated at 55 FR 35561, Aug. 31, 1990, as amended at 56 FR 66784, Dec. 26, 1991]


Download our app to see the most-to-date content.