When § 172.101 of this subchapter specifies that a hazardous material be packaged under this section, only the following bulk packagings are authorized, subject to the requirements of subparts A and B of part 173 of this subchapter and the special provisions specified in column 7 of the § 172.101 table.
(a) Rail cars:
(1) Class DOT 105, 109, 112, 114, or 120 fusion-welded tank car tanks; and Class 106 or 110 multi-unit tank car tanks. For tank car tanks built prior to March 16, 2009, the following conditions apply:
(i) Division 6.1 Hazard Zone A materials must be transported in tank cars having a test pressure of 34.47 Bar (500 psig) or greater and conform to Classes 105J, 106 or 110.
(ii) Division 6.1 Hazard Zone B materials must be transported in tank cars having a test pressure of 20.68 Bar (300 psig) or greater and conform to Classes 105S, 106, 110, 112J, 114J or 120S.
(iii) Hydrogen fluoride, anhydrous must be transported in tank cars having a test pressure of 20.68 Bar (300 psig) or greater and conform to Classes 105, 112, 114 or 120.
(2) For materials poisonous by inhalation, single unit tank cars tanks built prior to March 16, 2009 and approved by the Tank Car Committee for transportation of the specified material. Except as provided in § 173.244(a)(3), tank cars built on or after March 16, 2009 used for the transportation of the PIH materials listed below, must meet the applicable authorized tank car specification listed in the following table:
Table 1 to Paragraph (a)(2)
| Proper shipping name | Authorized tank car specification |
|---|---|
| Acetone cyanohydrin, stabilized (Note 1) | 105H500W, 112H500W |
| Acrolein (Note 1) | 105H600W |
| Allyl Alcohol | 105H500W, 112H500W |
| Bromine | 105H500W |
| Chloropicrin | 105H500W, 112H500W |
| Chlorosulfonic acid | 105H500W, 112H500W |
| Dimethyl sulfate | 105H500W, 112H500W |
| Ethyl chloroformate | 105H500W, 112H500W |
| Hexachlorocyclopentadiene | 105H500W, 112H500W |
| Hydrocyanic acid, aqueous solution or Hydrogen cyanide, aqueous solution with not more than 20% hydrogen cyanide (Note 2) | 105H500W, 112H500W |
| Hydrogen cyanide, stabilized (Note 2) | 105H600W |
| Hydrogen fluoride, anhydrous | 105H500W, 112H500W |
| Poison inhalation hazard, Zone A materials not specifically identified in this table | 105H600W |
| Poison inhalation hazard, Zone B materials not specifically identified in this table | 105H500W, 112H500W |
| Phosphorus trichloride | 105H500W, 112H500W |
| Sulfur trioxide, stabilized | 105H500W, 112H500W |
| Sulfuric acid, fuming | 105H500W, 112H500W |
| Titanium tetrachloride | 105H500W, 112H500W |
(3) As an alternative to the authorized tank car specification listed in the table in paragraph (a)(2) of this section, a car of the same authorized tank car specification but of the next lower test pressure, as prescribed in column 5 of the table at § 179.101-1 of this subchapter, may be used provided that both of the following conditions are met:
(i) The difference between the alternative and the required minimum plate thicknesses, based on the calculation prescribed in § 179.100-6 of this subchapter, must be added to the alternative tank car jacket and head shield. When the jacket and head shield are made from steel with a minimum tensile strength from 70,000 p.s.i. to 80,000 p.s.i., but the required minimum plate thickness calculation is based on steel with a minimum tensile strength of 81,000 p.s.i., the thickness to be added to the jacket and head shield must be increased by a factor of 1.157. Forming allowances for heads are not required to be considered when calculating thickness differences.
(ii) The tank car jacket and head shield are manufactured from carbon steel plate as prescribed in § 179.100-7(a) of this subchapter.
(b) Cargo tanks: Specifications MC 330 and MC 331 cargo tank motor vehicles and, except for Division 4.2 materials, MC 312 and DOT 412 cargo tank motor vehicles.
(c) Portable tanks: DOT 51 portable tanks and UN portable tanks that meet the requirements of this subchapter, when a T code is specified in Column (7) of the § 172.101 Table of this subchapter for the specific hazardous material, are authorized. Additionally, a DOT 51 or UN portable tank used for Division 6.1 liquids, Hazard Zone A or B, must be certified and stamped to the ASME Code as specified in § 178.273(b)(6) of this subchapter.
[Amdt. 173-224, 55 FR 52663, Dec. 21, 1990, as amended at 56 FR 66275, Dec. 20, 1991; 57 FR 45463, Oct. 1, 1992; Amdt. 173-252, 61 FR 28676, June 5, 1996; 68 FR 45037, July 31, 2003; 72 FR 55693, Oct. 1, 2007; 74 FR 1799, Jan. 13, 2009; 85 FR 75714, Nov. 25, 2020]